LeapFrog Epic: Difference between revisions
(15 intermediate revisions by the same user not shown) | |||
Line 8: | Line 8: | ||
*Display: 7-inch capacitive touchscreen with TN LCD display | *Display: 7-inch capacitive touchscreen with TN LCD display | ||
*Resolution: 1024x600 | *Resolution: 1024x600 | ||
*Operating System: Android 4.4.2 "KitKat" (MT8127 models) | *Operating System: | ||
*Processor: Quad-core, 1.3 GHz MediaTek MT8127 | ** Android 4.4.2 "KitKat" (MT8127 models) | ||
** Android 10 (Rockchip models; the Rockchip variant can also boot generic system images up to Android 14) | |||
*Processor: | |||
** Quad-core, 1.3 GHz MediaTek MT8127 | |||
** Later (2021) LeapPad Academy SKUs replace it with a 1.5 GHz Rockchip RK3326 | |||
*Memory: 1GB RAM | *Memory: 1GB RAM | ||
*Storage: 16GB; ~9GB available for /sdcard partition | *Storage: 16GB; ~9GB available for /sdcard partition | ||
Line 66: | Line 70: | ||
===Signed ROM backups=== | ===Signed ROM backups=== | ||
If you're getting a signature error upon flashing, try unticking SEC_RO and then try again. You might also want to flash the whole package in case you get a boot logo loop especially after flashing a TWRP recovery image. | |||
====Epic Academy Edition==== | ====Epic Academy Edition==== | ||
* [https://androidfilehost.com/?fid=6006931924117902657 v1.1.95] | * [https://androidfilehost.com/?fid=6006931924117902657 v1.1.95] | ||
Line 74: | Line 80: | ||
* [https://androidfilehost.com/?fid=4349826312261738402 v1.1.171] | * [https://androidfilehost.com/?fid=4349826312261738402 v1.1.171] | ||
====LeapPad Academy (second-generation)==== | |||
* [https://archive.org/details/leapfrog-epicv4-firmware Internet Archive page] | |||
* [https://www.androidfilehost.com/?fid=9180008750105244111 EPIC4.user.1.7.2109.312280833] ([https://drive.google.com/file/d/13TB0eCUFWSyyq5E0nM4RVBH9hpMxQ2XI/view Google Drive mirror]) | |||
* [https://archive.org/details/leapfrog-epicv4-firmware_MIPI EPIC4.user.2.6.2196.402290923 (MIPI variant)] | |||
===Demo to retail conversion=== | ===Demo to retail conversion=== | ||
Line 81: | Line 90: | ||
===Google Apps and root=== | ===Google Apps and root=== | ||
*[https://www.youtube.com/watch?v=56XdXJbFbjQ Install TWRP, Google Play and SuperSU root on your LeapFrog Epic] | *[https://www.youtube.com/watch?v=56XdXJbFbjQ Install TWRP, Google Play and SuperSU root on your LeapFrog Epic] | ||
*The original MT8127 Epic/LeapPad Academy firmware is vulnerable to the [[wikipedia:Dirty COW|Dirty COW]] exploit where a temporary root shell can be obtained via ADB. | |||
*The Rockchip RK3326 revision LeapPad Academy on the other hand can be rooted by patching the boot image using Magisk, but doing so breaks wireless functionality at least with the latest version. Ditto with the MT8127 version, but in that case the real-time clock seems to be a little sketchy with Magisk enabled, not to mention that they may no longer have support for early Android versions at the time of this writing. | |||
===Useful apps=== | ===Useful apps=== | ||
Line 94: | Line 105: | ||
*[http://repo.xposed.info/module/de.robv.android.xposed.installer Xposed Installer] is also a must-have when rooted, as it allows you to do all sorts of neat stuff like restoring lost functionality as described [http://spiffyhacks.com/thread-1080-post-6056.html#pid6056 here]. | *[http://repo.xposed.info/module/de.robv.android.xposed.installer Xposed Installer] is also a must-have when rooted, as it allows you to do all sorts of neat stuff like restoring lost functionality as described [http://spiffyhacks.com/thread-1080-post-6056.html#pid6056 here]. | ||
== | ===Rockchip hardware revision (EPICv4; 2021)=== | ||
[ | LeapFrog also [https://fccid.io/G2R-6022 quietly released a hardware revision] of the Epic circa 2021, replacing the MT8127 with a Rockchip RK3326. While this allowed LeapFrog to upgrade the included operating system to Android 10, it also means that the change in hardware rendered most hacks designed for the original Epic obsolete. | ||
VTech more or less nerfed the device by disabling features such as ADB and development settings, though USB debugging can be restored by temporarily rooting the device by patching boot.img with Magisk and editing the ADB setting using a settings database editor such as [https://play.google.com/store/apps/details?id=by4a.setedit22&hl=en&gl=US SetEdit]. Bizarrely enough they also dropped Bluetooth, replacing the wireless module with an obscure AltoBeam ATBM6011 wireless LAN controller. | |||
Ripping the firmware also used to be a challenge due to the uboot binary coded with a deterrent which corrupts the dumped images past a certain point. To be fair this is hardly even unique to LeapFrog as the implementation by Rockchip themselves [https://gitlab.com/pgwipeout/u-boot-rockchip/-/blob/1b01cf5590f8d0b2270ffff5a656e38c5e3930ee/cmd/rockusb.c#L28 has this] until the [https://gitlab.com/pgwipeout/u-boot-rockchip/-/blob/6336d2324985831ed766031f91d410d0e587dbc8/cmd/rockusb.c latest commit]. However, an update to RedScorpio's [https://xdaforums.com/t/tool-imgrepackerrk-rockchips-firmware-images-unpacker-packer.2257331/post-89464941 imgRePackerRK] tool now made it possible to patch the stock uboot and enable firmware dumping. | |||
In case of a brick, it is possible to unbrick the LeapPad by forcing it to run in MASKROM mode through shorting two conveniently-located test points on the logic board just beside the eMMC chip, though it may also be rather fiddly to pull off; a small reset switch may be soldered onto the testpoints like those generic TV boxes running off similar Rockchip hardware. | |||
It is also (theoretically) possible to boot from an SD card with a firmware image flashed onto it. Performance with such a setup would be unsurprisingly bad compared to a ROM flashed into internal storage, but it should be fine for testing if the firmware dump works fine or for recovering from a bricked tablet. | |||
As the second-gen LeapPad Academy supports Project Treble, generic system images (GSIs) are bootable even up to [https://www.youtube.com/watch?v=UWrepWibbtc Android 14], though performance and battery life ''will'' suffer with it; earlier versions such as 10 and 11 should run with fewer issues. | |||
There are also two sub-variants of the EPICv4, with internal and firmware differences that are subtle on the surface but are still enough that firmware for each other isn't cross-compatible. Firmware for the non-MIPI variant bear the <tt>EPIC4.user.1.x.xxxx.xxxxxxxxx</tt> build number, while those on the MIPI variant use <tt>EPIC4.user.2.x.xxxx.xxxxxxxxx</tt> builds. Apparently the display module and driver on the MIPI version is different compared to the non-MIPI units as round objects appear more elongated on the latter due to the display using non-square pixels to force a "16:9" ratio, similar to countless discount Android tablets. | |||
====Gallery==== | ====Gallery==== | ||
Line 108: | Line 124: | ||
File:RK3326 LeapPad.jpg|The LeapPad in action. | File:RK3326 LeapPad.jpg|The LeapPad in action. | ||
File:RK3326 LeapPad internals.jpg|Internals | File:RK3326 LeapPad internals.jpg|Internals | ||
File:LeapPad Academy Treble compatibility.jpg|Yup, GSIs should now work on this one, though a dedicated custom ROM would be ideal due to some software issues | |||
File:ATBM 6011.jpg|AltoBeam ATBM6011 wireless LAN module | File:ATBM 6011.jpg|AltoBeam ATBM6011 wireless LAN module | ||
File:RK3326 LeapPad MASKROM testpoints.jpg|Short those two pins beside the eMMC chip to boot into MASKROM mode. | File:RK3326 LeapPad MASKROM testpoints.jpg|Short those two pins beside the eMMC chip to boot into MASKROM mode. | ||
</gallery> | </gallery> | ||
==Misc. notes== | |||
[[File:Epic DiSA lock.jpg|thumb|200px|right|Trust me, I bought this thing.]] | |||
*Apparently, certain North American SKUs of the Epic especially those made after March 2017, come with a product activation scheme designed to deter shoplifting, i.e. black-market reselling of stolen goods. Upon purchase of the Epic (or any other tablet with such a scheme), users are prompted to enter a code given by the seller, or retrieving an activation code off [https://getyourcode.com/ this site]. One hacker claimed to be offering a workaround for this issue, and this may be defeated through other means, but for legal reasons I may not come up with a workaround for this unless a user with an affected Epic has enough evidence that their Epic is legitimately purchased. | |||
*Also, those on build 1.7.18 (KOT49H.user.1.7.18.20170327.110821) may experience streaming video issues with sites such as YouTube, LeapSearch, Netflix or Vimeo regardless of client. They video may play for a moment, but will eventually glitch out and/or outright stop with an error. No fix has been made by LeapFrog yet as of {{CURRENTMONTHNAME}} {{CURRENTYEAR}}, much to the dismay of irate parents who took to Facebook and expressed their dismay over VTech/LeapFrog's handling of the bug. A workaround would be to [https://www.youtube.com/watch?v=OpUgI8ZSkP4 flash the signed Academy Edition 1.1.95 ROM] using SP Flash Tool. | |||
[[Category:Android]] | [[Category:Android]] |