LeapFrog Epic: Difference between revisions

Line 112:

Ripping the firmware also used to be a challenge due to the uboot binary coded with a deterrent which corrupts the dumped images past a certain point. To be fair this is hardly even unique to LeapFrog as the implementation by Rockchip themselves [https://gitlab.com/pgwipeout/u-boot-rockchip/-/blob/1b01cf5590f8d0b2270ffff5a656e38c5e3930ee/cmd/rockusb.c#L28 has this] until the [https://gitlab.com/pgwipeout/u-boot-rockchip/-/blob/6336d2324985831ed766031f91d410d0e587dbc8/cmd/rockusb.c latest commit]. However, an update to RedScorpio's [https://xdaforums.com/t/tool-imgrepackerrk-rockchips-firmware-images-unpacker-packer.2257331/post-89464941 imgRePackerRK] tool now made it possible to patch the stock uboot and enable firmware dumping.

In case of a brick, it is possible to unbrick the LeapPad by forcing it to run in MASKROM mode through shorting two conveniently-located test points on the logic board just beside the eMMC chip, though it may also be rather fiddly to pull off.

In case of a brick, it is possible to unbrick the LeapPad by forcing it to run in MASKROM mode through shorting two conveniently-located test points on the logic board just beside the eMMC chip, though it may also be rather fiddly to pull off; a small reset switch may be soldered onto the testpoints like those generic TV boxes running off similar Rockchip hardware.

It is also possible to boot from an SD card with a firmware image flashed onto it. Performance with such a setup would be unsurprisingly bad compared to a ROM flashed into internal storage, but it should be fine for testing if the firmware dump works fine or for recovering from a bricked tablet.

It is also (theoretically) possible to boot from an SD card with a firmware image flashed onto it. Performance with such a setup would be unsurprisingly bad compared to a ROM flashed into internal storage, but it should be fine for testing if the firmware dump works fine or for recovering from a bricked tablet.

As the second-gen LeapPad Academy supports Project Treble, generic system images (GSIs) are bootable even up to [https://www.youtube.com/watch?v=UWrepWibbtc Android 14], though performance and battery life ''will'' suffer with it; earlier versions such as 10 and 11 should run with fewer issues.

@@ Line 112: / Line 112: @@
 Ripping the firmware also used to be a challenge due to the uboot binary coded with a deterrent which corrupts the dumped images past a certain point. To be fair this is hardly even unique to LeapFrog as the implementation by Rockchip themselves [https://gitlab.com/pgwipeout/u-boot-rockchip/-/blob/1b01cf5590f8d0b2270ffff5a656e38c5e3930ee/cmd/rockusb.c#L28 has this] until the [https://gitlab.com/pgwipeout/u-boot-rockchip/-/blob/6336d2324985831ed766031f91d410d0e587dbc8/cmd/rockusb.c latest commit]. However, an update to RedScorpio's [https://xdaforums.com/t/tool-imgrepackerrk-rockchips-firmware-images-unpacker-packer.2257331/post-89464941 imgRePackerRK] tool now made it possible to patch the stock uboot and enable firmware dumping.
-In case of a brick, it is possible to unbrick the LeapPad by forcing it to run in MASKROM mode through shorting two conveniently-located test points on the logic board just beside the eMMC chip, though it may also be rather fiddly to pull off.
+In case of a brick, it is possible to unbrick the LeapPad by forcing it to run in MASKROM mode through shorting two conveniently-located test points on the logic board just beside the eMMC chip, though it may also be rather fiddly to pull off; a small reset switch may be soldered onto the testpoints like those generic TV boxes running off similar Rockchip hardware.
-It is also possible to boot from an SD card with a firmware image flashed onto it. Performance with such a setup would be unsurprisingly bad compared to a ROM flashed into internal storage, but it should be fine for testing if the firmware dump works fine or for recovering from a bricked tablet.
+It is also (theoretically) possible to boot from an SD card with a firmware image flashed onto it. Performance with such a setup would be unsurprisingly bad compared to a ROM flashed into internal storage, but it should be fine for testing if the firmware dump works fine or for recovering from a bricked tablet.
 As the second-gen LeapPad Academy supports Project Treble, generic system images (GSIs) are bootable even up to [https://www.youtube.com/watch?v=UWrepWibbtc Android 14], though performance and battery life ''will'' suffer with it; earlier versions such as 10 and 11 should run with fewer issues.